Skip to main content

Find a device

There are three ways to reach a device:
  • Places, in the sidebar: open a region, building and room, then select the device.
  • Devices, in the sidebar: search by name, room, address or protocol, and filter by status, type and room tag.
The type filter uses the device categories: Display, Conferencing, Audio, Camera, Control, AV-over-IP and Power. The room tag filter, All room tags, shows only if your organisation has room tags.
  • Overview: select a summary card or building tile to open a filtered list.
When you arrive at Devices from a region, building, room or Collector, the filter shows as a chip at the top, such as Building: North Wing. Select the chip’s cross to clear it. The list refreshes every 30 seconds.

The device page

Select View on a device to open its page. The header shows its status, location, type, protocol and make and model, when it was Last contacted, and when the page last updated. Last contacted is the last time the device reported online. It turns amber while the device isn’t online. The header has these buttons:
  • Refresh reloads the page.
  • Reconnect and Edit (see below).
  • Delete removes the device, after you confirm. You need the Manage devices permission.
  • Touch Panel opens a touch panel’s own page, for Aurora RXT panels and devices with a touch_panel_path tag. See Touch Panel.
Sony displays also show their power state next to their status: Power on, Standby or Off. A display in standby still answers on the network, so it shows as Online as well. The power state shows on the Devices list too. Video codecs show their call state next to their status in the same way: In a call (or In 2 calls), Ringing, Connecting, On hold, Ending call or Idle. This call-status pill shows on the Devices list and the device page while the codec is online. Cisco and Poly codecs report it; see Supported devices.

Device Information

Device Information shows everything the device reports, refreshed every 10 seconds: identity such as model, serial number and firmware version, network details, and the device’s own readings, such as power state, input, volume or temperature. Which readings appear depends on the device; see Supported devices. If the device reports faults, Fault Count and Faults appear first. Select a list to expand it. Devices with several outlets or ports, such as a PDU or a network switch, show them in Outlets and Ports tables, with one row for each outlet or port and one column for each reading. Devices that report levels, such as a DSP with subscribed levels, show them in a Levels card, not in Device Information.

Commands

Commands has a button for each command the device supports, such as Power On, Mute or Input Hdmi1. Some commands ask for a value first: a preset number, a volume level, a switch port or a dial address. Each command shows OK and how long it took, or the error the device returned. You need the Send device commands permission to see commands. If the device’s Collector is offline, a command waits up to 10 minutes for it to come back. After that the command is cancelled, so it can’t run unexpectedly later.
Video codecs running as a Microsoft Teams Rooms or Zoom Rooms appliance show Control disabled — appliance mode. Their readings stay live, but the device itself refuses commands.

Events

Recent events shows the last five changes, such as a device going offline or recovering, or an input changing. For the full history, select Activity.

Activity

Select Activity in the header to see every change made to the device and every command sent to it: who did it, when, and what changed.

Web interface

Select Web interface in the header to open the device’s own web page in a new browser tab: a display’s settings page, a DSP’s control page, a PDU’s outlet page. The page is relayed through the device’s Collector, so it works from anywhere, without being on the device’s network or using a VPN.
  1. Select Web interface.
  2. Leave Protocol and Port on Automatic, or choose them if the device’s web page is somewhere else. If the device’s web page doesn’t start at its home page, enter the page in Path, such as /login.
  3. Select Open in new tab. Sign in to the device as you would on site.
Automatic uses the scheme and port in the device’s address when it’s a web address, such as https://10.0.4.21:8443, or the device’s web_port tag. Otherwise it’s HTTP on port 80. Only ports 80, 443, 8080 and 8443, the device’s own port and its web_port tag can be opened, and only on that device’s own address. To open a device on the same page every time, give it a web_path tag, such as web_path: /login. Edit the device and add the tag under Tags. Path then starts with that page unless you enter another. Each session:
  • opens only in the browser that started it. The link works once, within 5 minutes.
  • ends after 15 minutes without activity, or after 8 hours. Start a new one to carry on.
  • is recorded in the audit log, with who opened it, how long it lasted and how much data it moved.
The Web interface window lists the device’s open sessions. Select End to end one straight away. You need the Remote access permission, which administrators have. The device’s Collector must be online and on version 1.0.41 or later. If it isn’t, the portal says the Collector isn’t connected for remote access; it may need updating to the latest version.
Only the device’s web page is relayed. Remote desktop, SSH and Telnet aren’t available yet.

Touch Panel

Touch Panel appears on Aurora RXT touch panels and on any device with a touch_panel_path tag, on the device page and in the device list. Select it to open the panel’s own page in a new browser tab, relayed through the device’s Collector over HTTPS in the same way as Web interface, so it works from anywhere. The session is recorded in the audit log like any other. The page opened is the device’s touch_panel_path tag, such as touch_panel_path: /user. Without the tag it’s /user. You need the Remote access permission. Without it, Touch Panel links straight to the panel’s address on your network instead, which works only from a computer that can reach the panel.

If a device isn’t responding

1

Check its status

Collector offline means the problem is the Collector, not the device. Check the Collector’s host and network first.
2

Reconnect

Select Reconnect in the header. The Collector drops its connection to the device and starts a new one, which clears most stuck sessions.
3

Power-cycle it

If the device is on a supported PDU or a PoE switch port, power-cycle it from that device’s Commands: Outlet Reboot on the PDU, or Poe Reset on the switch.

Send a command to many devices

  1. On Devices, select Send to group.
  2. Enter the Command name, such as power_off, and any arguments in Args (JSON, optional).
  3. Choose the devices, or use Select visible to take everything matching your search. You can narrow the list by building or room tag first.
  4. Select Send to and the number of devices, such as Send to 12 devices.
Each device runs the command if it has it, and the summary shows how many were queued and how many failed. Follow up on individual devices from their pages. You need the Bulk command fan-out permission.

Add or change a device

Administrators with the Manage devices permission can select New device on the Devices page, or Edit on a device page. See Supported devices for what to enter for each kind of device. In Tags, select Add tag to give the device a tag name and value. Tag names can’t contain spaces. Tags you add stay saved. Leave Poll rate (seconds) blank to use the default for the kind of device: every 60 seconds for most, every 5 minutes for ATEN power distribution units, which log in for each reading. Set a value only where you need faster or slower updates.

Move a device to another Collector

Edit the device and choose a different Collector. When you save, the device moves with its history, alerts and settings, and both Collectors pick up the change within seconds. The move is refused if the other Collector already has a device with the same Reported ID. To move every device off a failed Collector at once, use Replace on the Collectors page. See Replace a failed Collector.

Updated 06 Nov 2026 14:07 · page 468ac7c