> ## Documentation Index
> Fetch the complete documentation index at: https://docs.marcus.involvecloud.com/llms.txt
> Use this file to discover all available pages before exploring further.

# Philips Professional Displays

> Philips professional and signage displays over SICP on TCP port 5000. Power, inputs, volume, mute and backlight; temperature, signal presence, operating hours and identity. Wake-on-LAN for power-on from deep standby.

**Works with:** Philips professional displays from PPDS that support SICP over the network, including the Q-Line, D-Line and T-Line signage and meeting-room ranges.

| | |
| - | - |
| **Type** | Vendor adapter |
| **Vendor** | Philips (PPDS) |
| **Device types** | Display |
| **Connection** | SICP over TCP (port 5000), with Wake-on-LAN for power-on |
| **Power on/off from the portal** | Yes |
| **Protocol in the portal** | Philips Professional Displays (`philips_sicp`) |

## Before you start

1. Connect the display to the network and note its IP address. SICP over the network uses port 5000.
2. Check the display's **Monitor ID** in its menu (default 1). If it isn't 1, set the `monitor_id` tag.
3. So that the display can be powered on remotely, either set its advanced power management (**APM**) to keep the network on in standby (TCP on), or set the `mac_address` tag and turn on Wake-on-LAN.

## Add the device

1. In the portal, go to **Devices** and select **New device**.
2. Choose the **Collector** that can reach the device, and set **Protocol** to **Philips Professional Displays**.
3. Enter the settings below and save. The Collector picks up the new device within seconds.

| Setting | Required | What to enter | Example |
| - | - | - | - |
| **Address** | Yes | Display IP or hostname. Port 5000 is the SICP default; append :port to override. | `192.168.30.50` |
| **Tags → `monitor_id`** | No | The display's Monitor ID (1–255), set in its menu. Defaults to 1. | `1` |
| **Tags → `mac_address`** | No | MAC address for Wake-on-LAN, so power\_on works when the display's network sleeps in standby. | `AA:BB:CC:11:22:33` |

> [!NOTE]
>
> **Tags** are set in the **Tags** section of the device form: select **Add tag**, then enter the name and value, for example `monitor_id` = `1`.

## Readings

These values appear under **Device Information** on the device page, and can be checked in Room Readiness routines.

| Reading | Shown as |
| - | - |
| `power_status` | Power Status |
| `current_input` | Current Input |
| `signal_present` | Signal Present |
| `backlight` | Backlight |
| `volume` | Volume |
| `volume_audio_out` | Volume Audio Out |
| `mute` | Mute |
| `temperature_c` | Temperature C |
| `temperature_N_c` | Temperature N C |
| `operating_hours` | Operating Hours |
| `model` | Model |
| `firmware_version` | Firmware Version |
| `serial_number` | Serial Number |
| `response_ms` | Response Ms |

## Commands

Each command is a button on the device page, and can be used in Room Readiness routines.

| Command | Button | Notes |
| - | - | - |
| `power_on` | Power On | |
| `power_off` | Power Off | |
| `input_hdmi1` | Input Hdmi1 | |
| `input_hdmi2` | Input Hdmi2 | |
| `input_hdmi3` | Input Hdmi3 | |
| `input_hdmi4` | Input Hdmi4 | |
| `input_displayport` | Input Displayport | |
| `input_dvi` | Input Dvi | |
| `input_vga` | Input Vga | |
| `input_ops` | Input Ops | |
| `set_volume` | Set Volume | Asks for the level, 0–100. |
| `volume_up` | Volume Up | |
| `volume_down` | Volume Down | |
| `mute` | Mute | |
| `unmute` | Unmute | |
| `backlight_on` | Backlight On | |
| `backlight_off` | Backlight Off | |
| `reboot` | Reboot | |

> [!NOTE]
>
> **Standby:** while the display is in standby it reports its power state, operating hours and identity; input, volume, signal and temperature readings return when it's switched on.

> [!NOTE]
>
> **Backlight off** blanks the picture but leaves audio playing, which suits rooms where the screen should go dark without a full power-off.

> [!NOTE]
>
> **Older models:** some older platforms only accept the short form of the volume commands. M.A.R.C.U.S. retries with that form automatically.

Updated 06 Nov 2026 14:07 · page 87abf8a


This documentation is built and hosted on [Mintlify](https://mintlify.com), a developer documentation platform.