> ## Documentation Index
> Fetch the complete documentation index at: https://docs.marcus.involvecloud.com/llms.txt
> Use this file to discover all available pages before exploring further.

# NEC projector

> NEC and Sharp NEC projectors, such as the PA-series laser models, over NEC's projector control protocol on TCP port 7142. Power, input, picture and sound mute, volume and lens shutter; power state including warming up and cooling down, input and signal, light-source and filter hours, faults and identity.

**Works with:** NEC and Sharp NEC projectors that support NEC's projector control commands over the network, including the PA-series laser models such as the NP-PA804UL and NP-PA1004UL.

| | |
| - | - |
| **Type** | Vendor adapter |
| **Vendor** | Sharp NEC |
| **Device types** | Projector |
| **Connection** | NEC projector control protocol over TCP (port 7142) |
| **Power on/off from the portal** | Yes |
| **Protocol in the portal** | NEC projector (`nec_projector`) |

## Before you start

1. Connect the projector's LAN port to the network and note its IP address. Control commands use TCP port 7142.
2. So that the projector can be monitored and switched on while in standby, set its **Standby Mode** to **Normal** or **Network Standby**, not a power-saving mode that turns the network off.
3. If **Control ID** is turned on in the projector's menu, set the `control_id` tag to the same number.

## Add the device

1. In the portal, go to **Devices** and select **New device**.
2. Choose the **Collector** that can reach the device, and set **Protocol** to **NEC projector**.
3. Enter the settings below and save. The Collector picks up the new device within seconds.

| Setting | Required | What to enter | Example |
| - | - | - | - |
| **Address** | Yes | Projector IP or hostname. Port 7142 is the NEC control port default; append :port to override. | `192.168.30.60` |
| **Tags → `control_id`** | No | The projector's Control ID (1–254), only if Control ID is turned on in its menu. | `1` |

> [!NOTE]
>
> **Tags** are set in the **Tags** section of the device form: select **Add tag**, then enter the name and value, for example `control_id` = `1`.

## Readings

These values appear under **Device Information** on the device page, and can be checked in Room Readiness routines.

| Reading | Shown as |
| - | - |
| `power_status` | Power Status |
| `operation_status` | Operation Status |
| `current_input` | Current Input |
| `signal_present` | Signal Present |
| `display_content` | Display Content |
| `picture_mute` | Picture Mute |
| `sound_mute` | Sound Mute |
| `onscreen_mute` | Onscreen Mute |
| `volume` | Volume |
| `light_source_hours` | Light Source Hours |
| `light_source_life_pct` | Light Source Life Pct |
| `filter_hours` | Filter Hours |
| `fault_count` | Fault Count |
| `faults` | Faults |
| `model` | Model |
| `serial_number` | Serial Number |
| `mac_address` | Mac Address |
| `response_ms` | Response Ms |

## Commands

Each command is a button on the device page, and can be used in Room Readiness routines.

| Command | Button | Notes |
| - | - | - |
| `power_on` | Power On | |
| `power_off` | Power Off | |
| `input_hdmi1` | Input Hdmi1 | |
| `input_hdmi2` | Input Hdmi2 | |
| `input_displayport` | Input Displayport | |
| `input_hdbaset` | Input Hdbaset | |
| `input_bnc_video` | Input Bnc Video | |
| `input_bnc_yc` | Input Bnc Yc | |
| `input_select` | Input Select | Asks for the input terminal code in hex, such as `A1` (HDMI1) or `BF` (HDBaseT). |
| `picture_mute` | Picture Mute | |
| `picture_unmute` | Picture Unmute | |
| `sound_mute` | Sound Mute | |
| `sound_unmute` | Sound Unmute | |
| `set_volume` | Set Volume | Asks for the level, 0–100. |
| `volume_up` | Volume Up | |
| `volume_down` | Volume Down | |
| `shutter_close` | Shutter Close | |
| `shutter_open` | Shutter Open | |

> [!NOTE]
>
> **Warming up and cooling down:** the projector accepts no other commands while it powers on or cools down. **Power Status** shows **warming** or **cooling** during that time, and a command sent then fails with a message saying so. **Power On** during cool-down is refused until cooling has finished.

> [!NOTE]
>
> **Standby:** in standby the projector reports its power state, light-source and filter hours, faults and identity; input, mute and volume readings return when it's switched on.

> [!NOTE]
>
> **One connection:** the Collector connects only for each poll or command, so a room control system can use the projector's control port in between.

> [!NOTE]
>
> **Firmware:** NEC's control commands don't report a firmware version, so these projectors don't appear on the **Firmware** page.

Updated 10 Nov 2026 13:55 · page bae9202


This documentation is built and hosted on [Mintlify](https://mintlify.com), a developer documentation platform.