> ## Documentation Index
> Fetch the complete documentation index at: https://docs.marcus.involvecloud.com/llms.txt
> Use this file to discover all available pages before exploring further.

# Cisco TC (TC7)

> Cisco TelePresence codecs on TC software (TC7.x): SX, MX, EX, C and Profile series. The same xAPI as RoomOS, with TC's standby and reboot commands and support for its older HTTPS.

**Works with:** Cisco TelePresence codecs running TC software (TC7.x), including the SX, MX, EX, C and Profile series. For CE or RoomOS software, use [Cisco RoomOS](https://docs.marcus.involvecloud.com/devices/cisco-roomos.md).

| | |
| - | - |
| **Type** | Vendor adapter |
| **Vendor** | Cisco |
| **Device types** | Conferencing |
| **Connection** | xAPI over HTTPS (TCP 443) or HTTP (TCP 80), using Basic authentication |
| **Power on/off from the portal** | Yes |
| **Protocol in the portal** | Cisco TC (TC7) (`cisco_tc`) |

## Before you start

1. Check the codec's software version in its web interface, under **System Information**. It starts `TC7` for this adapter.
2. Note the username and password of a user with the **Admin** role. On TC, the built-in `admin` user has it.
3. TC uses a self-signed certificate unless you've installed your own. If you haven't, set the `tls_skip_verify` tag to `true` on the device.

## Add the device

1. In the portal, go to **Devices** and select **New device**.
2. Choose the **Collector** that can reach the device, and set **Protocol** to **Cisco TC (TC7)**.
3. Enter the settings below and save. The Collector picks up the new device within seconds.

| Setting | Required | What to enter | Example |
| - | - | - | - |
| **Address** | Yes | Codec address. HTTPS is assumed; TC also enables HTTP by default, so http\:// works if HTTPS gives trouble. | `192.168.1.19` |
| **Username** | Yes | Local user with the Admin role (admin by default on TC). | |
| **Password** | Yes | That user's password. | |
| **Tags → `tls_skip_verify`** | No | Set to "true" to accept the codec's self-signed certificate. | `true` |

> [!NOTE]
>
> **Tags** are set in the **Tags** section of the device form: select **Add tag**, then enter the name and value, for example `tls_skip_verify` = `true`.

## Readings

These values appear under **Device Information** on the device page, and can be checked in Room Readiness routines.

| Reading | Shown as |
| - | - |
| `call_state` | Call State |
| `active_calls` | Active Calls |
| `remote_number` | Remote Number |
| `mic_mute` | Mic Mute |
| `volume` | Volume |
| `power_status` | Power Status |
| `standby_state` | Standby State |
| `product_id` | Product Id |
| `software_version` | Software Version |
| `serial_number` | Serial Number |
| `ip_address` | Ip Address |
| `mac_address` | Mac Address |
| `uptime_s` | Uptime S |
| `fault_count` | Fault Count |
| `faults` | Faults |
| `response_ms` | Response Ms |

## Commands

Each command is a button on the device page, and can be used in Room Readiness routines.

| Command | Button | Notes |
| - | - | - |
| `dial` | Dial | Asks for the address to dial: SIP URI, H.323 address or phone number. |
| `hangup` | Hangup | |
| `mute` | Mute | |
| `unmute` | Unmute | |
| `vol_up` | Vol Up | |
| `vol_dn` | Vol Dn | |
| `power_on` | Power On | |
| `power_off` | Power Off | |
| `reboot` | Reboot | |

> [!NOTE]
>
> **Older HTTPS:** TC's web server predates current TLS, so this adapter also accepts TLS 1.0 and 1.1 and older cipher suites. TC enables HTTP as well as HTTPS by default; if HTTPS still won't connect, enter the address as `http://` followed by the codec's IP address.

> [!NOTE]
>
> **Power:** **Power Off** puts the codec into standby and **Power On** wakes it. The device page shows the standby state as Off (awake) or Standby.

> [!NOTE]
>
> **Not available on TC:** people count, which needs RoomOS.

Updated 06 Nov 2026 14:07 · page a16abd7


This documentation is built and hosted on [Mintlify](https://mintlify.com), a developer documentation platform.